Question 1

Chris S.

Where is the Aeotec bypass? Aeotec's website still says that it will be available "early 2017", and yet here we are here in September and I cannot see much evidence of its availability. Does anyone have any insights into when it will be available? Thanks.

Asked 5 years ago 1 answer

Z-Wave Plus AEOTEC NANO DIMMER

Question 2

Sean M.

Is it possible to use these to control a 240v relay without chatter? We tried this by altering parameters 11,12 and 15 but were not successful. Any advice appreciated.

Asked 5 years ago 1 answer

Z-Wave Qubino Flush Relay x 2 Plus

Question 3

Alexander K.

hello - wanted to ask if the device provides data per phase or as a total. thanks!

Asked 5 years ago 0 answers

Z-Wave Plus AEOTEC-klem Machtsmeter - Drie klemmen (60A)

Question 4

Femi B.

Hi all, I have installed a couple of these (fgs223) on a 2 way switch. One is an on off switch and the other is a dimmer. I've put the switches behind the on off switch. That bit works well but now the separate dimmer won't dim it only switches on and off. Any suggestions?

Asked 5 years ago 4 answers

Z-Wave Fibaro Double Switch 2

Question 5

Khalidov S.

Z-Wave Fibaro KeyFob working with the Vera plus ?

Asked 5 years ago 0 answers

Z-Wave Fibaro KeyFob

Question 6

Sagi E.

Hey, will it work with the Vera Plus?

Asked 5 years ago 0 answers

Z-Wave Philio 2 * 1,5 KW-Relaiseinsätze

Question 7

JohnE

Does anyone know the trick to getting full functionality (press, press and hold, double press etc.) working with Domoticz?

Asked 5 years ago 0 answers

Z-Wave Remotec Scene Master

Question 8

Vicardo N.

Does anyone know how to reset this device if it was once included into a zwave controller in case the controller is no longer available?

Asked 5 years ago 1 answer

Z-Wave Plus MCO Home PM2.5 Air Quality Monitor - 12V

Question 9

Jason P.

Is the common connection a 3v output like the micro modules?

Asked 5 years ago 0 answers

Z-Wave Plus AEOTEC NANO DIMMER

Question 10

Nigel E.

When controlled by the local switch, can the level be controlled e.g. press briefly to turn on/off, press and hold to cycle the brightness?

Asked 5 years ago 1 answer

Z-Wave Plus AEOTEC NANO DIMMER

Question 11

Ian B.

Is anybody using this with Vera Plus and 1.7.2935 and, if so, how many functions per button is it now supporting ?

Asked 5 years ago 8 answers

Z-Wave Remotec Scene Master

Question 12

Michael G.

Hi there, I'm looking for a Z-wave dry contact switch, connected to my existing pilot wires from the boiler. Not really fussed about it being a thermostat, as all I need is to be able to remotely turn the heating on or off. I don't want to have to change out anything with the existing boiler's timer / programmer. I intend to leave it heating turned on at the boiler indefinitely, and the dry contact switch as the main on-off. I can then use scenes to control timing if need be. I don't think this Secure product is built for that since it needs replacing the boiler's timer / programmer. Can you kindly recommend a suitable product? Thanks in advance.

Asked 5 years ago 3 answers

Z-Wave Plus Secure Wall Thermostat with LCD display

Question 13

Sam

Is this suitable for powering a Zipabox controller?

Asked 5 years ago 0 answers

12V 30W Interchangeable Power Supply

Question 14

Duncan G.

Can this be used with the 2 channel boiler receiver? If so, how does it manage the hot water channel? I have a Razberry but wanted this to manage in the case of its failure (and because I understand it will manage the boiler better?)

Asked 5 years ago 3 answers

Z-Wave Plus Secure Wall Thermostat with LCD display

Question 15

David P.

I think I need this, since my LED lamp still glows a bit when it should be off, but am not clear on how it is meant to be fitted. The wiring diagram in the manual is hopeless - so do you have to put this inside the light fitting somehow ? I don't see where it would physically go, to bridge across the bulb. There are two lights driven by the same switch, so do I need to bypass them both ?

Asked 5 years ago 6 answers

Z-Wave Fibaro Dimmer Bypass 2

Question 16

Eyal L.

Is this Controller working with vera plus?

Asked 5 years ago 1 answer

Z-Wave Qubino Persiana enrasada Plus

Question 17

Jeremy M.

Is it possible to label the buttons on this unit? Previous controllers I have used in the past had clear plastic covers on the buttons that could be popped off and a slip of paper with the button's function slipped underneath.

Asked 5 years ago 3 answers

Z-Wave Remotec Scene Master

Question 18

ed b.

hello does anyone know if there is a template for the fibaro hc2 so it will work properly. thanks

Asked 5 years ago 0 answers

Z-Wave Philio 2 in 1 Temperature / Humidity Sensor - Gen5

Question 19

JohnE

What connectors do I need to order to extend this cable? I can get them from Farnell or RS if I know what are used. I'm assuming that this is a 1-wire sensor as it has three wires, pwr, gnd and the 1-wire bus, and that means that it can be extended to quite a few metres and I need to pick up the outside temperature...

Asked 5 years ago 4 answers

Qubino Temperatuursensor

Question 20

Mark C.

Can these be placed in an unfinished loft/attic? Some smoke detectors specifically state not to place them in an unfinished attic (e.g. Nest Protect) due to the large temp changes etc. Could not find anything specific re. these so thought I would pose the question here. Thanks chaps!

Asked 5 years ago 2 answers

Z-Wave Fibaro Smoke Sensor

Question 21

Nigel W.

Is there anyway to reset this device back to Factory settings?

Asked 5 years ago 3 answers

Z-Wave Plus Secure Wall Switch

Question 22

David F.

Does anyone know if you can control the LED colours from Vera Plus?

Asked 5 years ago 1 answer

Z-Wave Plus Aeotec Smart Switch 6 - UK

Question 23

Leonard v.

Does this item work with Fibaro HC2 please

Asked 5 years ago 1 answer

Z-WAVE POPP Z-regn

Question 24

Ian C.

Has this been proven to work with HomeSeer?

Asked 5 years ago 0 answers

Z-Wave Fibaro Pulsante

Question 25

andyhud

How many 240V GU10 Led Bulbs (Dimmable ones) can the FD2 support? I have 3 light fittings for outside my house that house 2 GU10 240 Bulbs or GU10 240V Dimmable Bulbs. I am going to use the LED Dimmable bulbs which on the box say "Use only 7 watts per bulb". So a total of 6 bulbs in 3 light housings. I'm going to wire them back to a junction box in parellel (not serial) and into then into the FB2 but was worried that 6 bulbs of this type (or even 10) would fry it? I have the original Fibaro Bypass Module also (FGB001) which I bought a few years ago but never used, could I use this if I need it? The LED 240v GU10 bulbs are "dimmable" Thanks! Andy

Asked 5 years ago 2 answers

Z-Wave Fibaro Universal Dimmer 2

Question 26

Michael W.

The product information mentions backup and restore feature. I understand this is to backup and restore the network to save on manually rebuilding the network in the situation of having to replace the stick (eg. if stick fails). Where can I find information about how to perform backup and restore?

Asked 5 years ago 3 answers

Z-Wave.Me USB Stick

Question 27

Mark C.

Why do these show as requiring a fuse whereas other like the Fibaro do not show this as a requirement in the wiring diagrams?

Asked 5 years ago 1 answer

Z-Wave Qubino Flush Relay x 2 Plus

Question 28

David F.

Does this work with Vera, if so can you also control the colour LED?

Asked 5 years ago 1 answer

Z-Wave Philio Smart Colour Button Gen5

Question 29

Karl L.

I read the following in the manual: Rated output power 8A for single output channel,13A at max.(3,25A for R.G.B.W. single output channel is suggested) I'm planing to control two strips of LED with the RGBW-Dimmer. Using two of the four channels. How much power (current) can each of the two LED-strips have? (I'm using a 24V driver). Maybe 13A/2 = 6.5A per channel?

Asked 5 years ago 1 answer

Z-WAVE QUBINO RGBW DIMMER PLUS

Question 30

jon p.

Do you think this product would be ok to control a cooker?

Asked 5 years ago 4 answers

Z-Wave Plus Aeotec Heavy Duty Switch

Question 31

Guest_v V.

Is this 2 wire compatible. i.e. Does it require a neutral?

Asked 5 years ago 1 answer

Z-Wave TKB Dual Paddle Wall Switch TZ36D - Gen5

Question 32

Barrie W.

Can this be connected to two bell-push switches, to activate two lighting scenes? The lights would be powered by other zwave modules (dimmers), so these would purely be used to trigger the scenes.

Asked 5 years ago 1 answer

Z-Wave Qubino Flush Relay x 2 Plus

Question 33

snap mac

hi is this light dependent . ie only work at night ? also does it work with n-cube controller?

Asked 5 years ago 0 answers

Z-Wave Philio Motion Capteur PSP05 - GEN5

Question 34

Phil P.

Hi, I had successfully setup 1x MultiSensor 6 (ZW100-C) which required a change of device type. I then purchased 2 more (same model, same firmware) but they have aren't detecting any motion. Is there any advice on how to resolve this? I have tried a number of different DTH, removing and repairing etc and now looking for some help.

Asked 5 years ago 0 answers

Z-Wave Más Aeotec MultiSensor 6

Question 35

Michael M.

Are there any special instructions for including this in a Vera Edge system. It seemed to install but will only notify about tampering and has no apparent reaction to movement other than a small fashing led. No notifications.

Asked 5 years ago 0 answers

Z-Wave Philio Motion Capteur PSP05 - GEN5

Question 36

Shukrie H.

Does this work with Vera Edge ?

Asked 5 years ago 0 answers

Z-Wave Philio Multisensor - Dør / PIR / Lys / Temp - Gen5

Question 37

jon s.

how do these perform with metal back boxes? Is there a significant reduction in effectiveness / range?

Asked 5 years ago 1 answer

Z-Wave Plus AEOTEC NANO DIMMER

Question 38

|Petr V.

Is this product working with VERA Plus - UI7? Any experiences with the setup and compatibility?

Asked 5 years ago 1 answer

Z-Wave Remotec AC IR extender

Question 39

Thiago H.

Is it possible to change colors of the light bulb using smartthings

Asked 5 years ago 1 answer

Z-Wave Plus AEOTEC NANO DIMMER

Question 40

Alastair F.

Does this need ventilation? I was planning on using these in the loft for the upstairs lighting and putting them in PVC boxes along with any connectors etc. This is to keep things neat and safe but wondered if I need to drill holes in the boxes for ventilation?

Asked 5 years ago 4 answers

Z-Wave Fibaro Universal Dimmer 2

Question 41

Scott R.

If I mount this in a roof, what's the max angle that it can be moved to in the horizontal & what's the andle of detection?

Asked 5 years ago 0 answers

Z-Wave Philio Motion Sensor PSP05 with Round Recessor - Gen5

Question 42

Guest_v V.

How is the quality of the key chain? It looks very frail as seen from the picture. I just wonder how long time it would survive in my keys

Asked 5 years ago 3 answers

Z-Wave Fibaro KeyFob

Question 43

Chris Male F.

Does this work on the standard European 868 zwave frequency ?

Asked 5 years ago 1 answer

Z-Wave Vision Door Lock without Handle

Question 44

Guest_v V.

What is new from the previous version. Looks pretty the same

Asked 5 years ago 1 answer

Z-Wave Fibaro Uniwersalny czujnik drzwi i okien 2

Question 45

ed b.

hello, does anyone know if this can be used with a fibaro hc2 and does it do anything else like lux, temp or humidity. thanks

Asked 5 years ago 3 answers

Z-Wave Philio Motion Capteur PSP05 - GEN5

Question 46

Huw T.

The uses states security gates, does this mean it's waterproof and suitable for outdoor use now?

Asked 5 years ago 2 answers

Z-Wave Fibaro Uniwersalny czujnik drzwi i okien 2

Question 47

Mark G.

Will it still accept an external temperature probe like the original model?

Asked 5 years ago 1 answer

Z-Wave Fibaro Uniwersalny czujnik drzwi i okien 2

Question 48

Jez A.

Hi. What wireless switch could I use with this dimmer? And do I need a 3rd party device (e.g. Vera or Smartthings) to configure them to talk to each other?

Asked 5 years ago 1 answer

Z-Wave Plus AEOTEC NANO DIMMER

Question 49

Michael S.

Hi, will two of these fit in a two gang wall box? I have both pendant and wall lights in my lounge

Asked 5 years ago 1 answer

Z-Wave Plus AEOTEC NANO DIMMER

Question 50

Sam L.

Use for a UK 2-wire (No neutral) switch with a 13W LED non-dimmable bulb in hallway, do I need to install with the bypass 2?

Asked 5 years ago 1 answer

Z-Wave Fibaro Universal Dimmer 2

Browse by Topic

Tools

Share This Page